Sachiya Steel International is one of the prominent Manufacture of high quality Stainless Steel 310H Wire Mesh, which Good resistance to mildly corrosive atmospheres, but significantly less than Grade 310H due to the Sulphur addition; the sulphide inclusions act as pit initiation sites. Â Grade 310 should not be exposed to marine or other similar environments, as these will result in rapid pitting corrosion. Because the sulphide inclusions in 310 are primarily aligned along the rolling direction the corrosion resistance is particularly reduced in cross-sections.
It is like other common austenitic stainless steels, is subject to stress corrosion cracking in chloride containing environments above about 50°C. Good oxidation resistance in intermittent service to 760°C and in continuous service to 870°C. Not generally recommended but, if unavoidable use Grade 308L or 309 electrodes. AS 1554.6 does not pre-qualify welding of 303.  Welds must be annealed for maximum corrosion resistance, but even then poor mechanical and corrosion properties will result.
For ultra-high machining rates there are also available special grade variants such as Ugima 303UX. This includes copper to reduce the work hardening rate, in addition to the usual high Sulphur and Improved Machinability steel making practices. Nuts and bolts. Bushings. Shafts. Electrical switchgear components. Gears. In general any component that is heavily machined and where the corrosion resistance and fabrication properties of 310H are viable. Grade 310H (UNS S31009) has a carbon content restricted to exclude the lower end of the 310 range, so is the grade of choice for high temperature applications.
SS 310H Wire mesh Specifications |
||
| Specifications | : | ASTM A 164 ASME SA 164 |
| Standard | : | DIN, ASTM, BS and all International Standards |
| Length | : | 30m to 100″ |
| Width | : | 1m to 48″ |
| Type | : | Wire Mesh , Hexagonal Wire mesh, Welding Wire mesh, Netting Wire mesh, Woven Wire mesh , Spring Steel wire mesh, Fencing Wire mesh etc. |
| Grade | C | Mn | Si | P | S | Cr | Mo | Ni | N |
| SS 310H | 0.04 – 0.10 | 2 max | 1.00 max | 0.045 max | 0.030 max | 24.00 – 26.00 | – | 19.00 – 21.00 | 53.885 min |
| Density | Melting Point | Tensile Strength | Yield Strength (0.2%Offset) | Elongation |
| 7.9 g/cm3 | 1402 °C (2555 °F) | Psi – 75000 , MPa – 515 | Psi – 30000 , MPa – 205 | 40% |
| STANDARD | WERKSTOFF NR. | UNS | JIS | BS | GOST | AFNOR | EN |
| SS 310H | – | S31009 | – | – | – | – | – |
SS 310H Wire Mesh Application Industries
- Off-Shore Oil Drilling Companies
- Power Generation
- Petrochemicals
- Gas Processing
- Specialty Chemicals
- Pharmaceuticals
- Pharmaceutical Equipment
- Chemical Equipment
- Sea Water Equipment
- Heat Exchangers
- Condensers
- Pulp and Paper Industry
We at Sachiya Steel International provide Manufacturer TC (Test Certificate) in accordance to EN 10204/3.1B, Raw Materials Certificate, 100% Radiography Test Report, Third Party Inspection Report. We also provide Standard certificates like EN 10204 3.1 and additional requirement like. NACE MR 01075. FERRIT CONTENT as per norms if requested by clients.
• EN 10204/3.1B,
• Raw Materials Certificate
• 100% Radiography Test Report
• Third Party Inspection Report, etc.
We at Sachiya Steel International ensure that all our materials go through strict quality tests before dispatching them to our clients.
• Mechanical Testing Such as Tensile of Area
• Hardness Test
• Chemical Analysis – Spectro Analysis
• Positive Material Identification – PMI Testing
• Flattening Test
• Micro and Macro Test
• Pitting Resistance Test
• Flaring Test
• Intergranular Corrosion (IGC) Test
• Commercial Invoice which includes HS Code
• Packing List including net weight and gross weight, number of boxes, Marks and Numbers
• Certificate of Origin legalized/attested by Chamber of Commerce or Embassy
• Fumigation Certificates
• Raw Material Test Reports
• Material Traceability Records
• Quality Assurance Plan (QAP)
• Heat Treatment Charts
• Test Certificates certifying NACE MR0103, NACE MR0175
• Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2
• Guarantee Letter
• NABL approved Laboratory Test Reports
• Welding Procedure Specification/Procedure Qualification Record, WPS/PQR
• Form A for the purposes of the Generalized System of Preferences (GSP)